TBS Podracer AIO 30A

Only 2 left in stock

Earn 98 Fox Coins worth 0.98

119.90

TBS Podracer AIO 30A is a powerful whoop board designed to cater for TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight core for your build.

TBS partnered with Zeez to make this awesome whoop AIO. Introducing the the TBS Podracer AIO, the board is designed to cater for TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight core for your build..

The FC is equipped with F4+MPU6000 and the ESC is capable of True 30A current running BLHeli32. This board is versitle enough to run on your cinewhoop, 4/5″ racer like the podracer and longrange cruiser like the TBS Aureo.

This AIO is your choice for you Foxiño!

 

TBS Podracer AIO 30A

Description

TBS Podracer AIO 30A is a powerful whoop board designed to cater for TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight core for your build.

TBS partnered with Zeez to make this awesome whoop AIO. Introducing the the TBS Podracer AIO 30A, the board is designed to cater for TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight core for your build..

The FC is equipped with F4+MPU6000 and the ESC is capable of True 30A current running BLHeli32. This board is versitle enough to run on your cinewhoop, 4/5″ racer like the podracer and longrange cruiser like the TBS Aureo.

FC SIDE

  • Mounting holes: 25.5×25.5 mm / M2 holes
  • Crossfire/Tracer RX CH1&2 > Uart 2  /  Pro32 Nano VTX > Uart 1 / Uart 1(RX) – unavailable.
  • Up to 6S input
  • 5V BEC up to 1.2A continuous
  • STM32F411 MCU (Support BetaFlight, EmuFlight)
  • MPU6000 Gyro/ACC
  • OSD chip Onboard (AT7456E)
  • 2 available UART
  • LC Filter for 5V VTX and Camera
  • Direct solder connection for TBS Nano RX and TBS Unify Pro32 Nano
  • Support programmable LED like WS2812 etc
  • Built-in current sensor

ESC SIDE

  • Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
  • Input voltage: 2S-6S Lipo
  • Continuous current: 30A
  • Peak current: 35A
  • ESC firmware: BLHELI 32
  • PWM Frequency Range: 24KHz up to 96KHz

GPS INSTALLATION

Because of the phyiscal limitations, installing a GPS module to the FC will require a few extra steps to remap the board’s resources.
Note: The following steps will disable LED and FC’s SmartAudio and use as softserial for GPS.

        1. Flash the board with Target: STM32F411

        2. Download the Config file [HERE]. Then load it the board.

        3. Wire the GPS as shown

INCLUDES
  • 1 x TBS Podracer AIO
  • 1 x Capacitor
  • 1 x AWG cables set with shrink tubes
  • 4 x mounting gromets
  • 1 x XT60 (Male)
  • 1 x XT30 (Male)
  • 1 x Pinheaders set for TBS VTX and RX

Additional information

Weight0.024 kg
Brand

Team Black Sheep

Reviews

There are no reviews yet.

Be the first to review “TBS Podracer AIO 30A”

Your email address will not be published. Required fields are marked *