ELRS Nano Receiver by BetaFPV

Sale!

Out of stock

Original price was: 19.99€.Current price is: 19.00€.

SKU ELRSNANO Categories , Tags , , , , , , ,

Elrs Nano receiver by Beta FPV is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
You can use it with this Transmitter Module for ELRS Express.

MANUAL

Specification

  • Weight: 0.7g (receiver only)
  • Size: 12mm*19mm
  • Telemetry power: 20dbm (100mW, 2.4G Version)
  • Frequency bands (Nano receiver 2.4G version): 2.4GHz ISM
  • Frequency bands (Nano receiver 915MHz/868MHz version): 915MHz FCC/868MHz EU
  • Input voltage: 5V
  • Antenna connector: IPEX MHF

Diagram

Nano receiver 2.4G version diagram as shown below.

elrs nano receiver

Nano receiver 868MHz/915MHz version diagram as shown below.

elrs nano receiver

Note: The firmware version of the Nano receiver and module manufactured by our company is ELRS 1.0.0-RC5 (the fifth test version before release);
ELRS Innovative team has officially released version 1.0.0. Based on the version, we have some updates:

  • 2.4G Nano TX Module supports 500Hz refresh rate;
  • Short press the button on the Nano module 3 times to get into the binding status.

We suggest our customers upgrade their modules and receivers’ ELRS version to 1.0.0. Significantly, the module and receiver have to be in the same ELRS version, otherwise, the frequency cannot match successfully.

Configuration & Bind

ExpressLRS uses the Crossfire serial protocol (AKA CRSF protocol) to communicate between the receiver and the flight controller board. So make sure your flight controller board supports the CRSF serial protocol. Next, we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol.

The connection between the ELRS Nano receiver and the FC board is shown below.

elrs nano receiver

Enable the corresponding UART (e.g. UART3 below) as a Serial Rx on Betaflight Configurator “Ports” tab.

On the “Configuration” tab, select “Serial-based receiver” on the “Receiver” panel, and select “CRSF” as the protocol. Telemetry is optional here and will reduce your stick update rate due to those transmit slots being used for telemetry.

Nano receiver could enter binding status by power on/off three times.

  • Plugin and unplug nano receiver three times;
  • Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode;
  • Make sure the RF TX module or radio transmitter enter binding status, which sends out a binding pulse;
  • If the receiver has a solid light, it’s bound.

 

ELRS Nano Receiver by BetaFPV

Description

Elrs Nano receiver by Beta FPV is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
You can use it with this Transmitter Module for ELRS Express.

MANUAL

Specification

  • Weight: 0.7g (receiver only)
  • Size: 12mm*19mm
  • Telemetry power: 20dbm (100mW, 2.4G Version)
  • Frequency bands (Nano receiver 2.4G version): 2.4GHz ISM
  • Frequency bands (Nano receiver 915MHz/868MHz version): 915MHz FCC/868MHz EU
  • Input voltage: 5V
  • Antenna connector: IPEX MHF

Diagram

Nano receiver 2.4G version diagram as shown below.

elrs nano receiver

Nano receiver 868MHz/915MHz version diagram as shown below.

elrs nano receiver

Note: The firmware version of the Nano receiver and module manufactured by our company is ELRS 1.0.0-RC5 (the fifth test version before release);
ELRS Innovative team has officially released version 1.0.0. Based on the version, we have some updates:

  • 2.4G Nano TX Module supports 500Hz refresh rate;
  • Short press the button on the Nano module 3 times to get into the binding status.

We suggest our customers upgrade their modules and receivers’ ELRS version to 1.0.0. Significantly, the module and receiver have to be in the same ELRS version, otherwise, the frequency cannot match successfully.

Configuration & Bind

ExpressLRS uses the Crossfire serial protocol (AKA CRSF protocol) to communicate between the receiver and the flight controller board. So make sure your flight controller board supports the CRSF serial protocol. Next, we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol.

The connection between the ELRS Nano receiver and the FC board is shown below.

elrs nano receiver

Enable the corresponding UART (e.g. UART3 below) as a Serial Rx on Betaflight Configurator “Ports” tab.

On the “Configuration” tab, select “Serial-based receiver” on the “Receiver” panel, and select “CRSF” as the protocol. Telemetry is optional here and will reduce your stick update rate due to those transmit slots being used for telemetry.

Nano receiver could enter binding status by power on/off three times.

  • Plugin and unplug nano receiver three times;
  • Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode;
  • Make sure the RF TX module or radio transmitter enter binding status, which sends out a binding pulse;
  • If the receiver has a solid light, it’s bound.

 

Additional information

Brand

Beta fpv

Reviews

There are no reviews yet.

Be the first to review “ELRS Nano Receiver by BetaFPV”

Your email address will not be published. Required fields are marked *

It seems like yestarday, but it’s been already 3 years of activity of our Company! To celebrate this goal we’ll be running super discounts on our webstore from July 11 to July 31

5% DISCOUNT ON ALL PRODUCTS
15% DISCOUNT ON FRAMES
up to 20% DISCOUNT ON PROPELLERS